A leading UK water and wastewater utility asked us to look at the concrete bund around a 96% sulphuric acid storage tank at one of its water treatment works near Bolton. The bund, approximately 3.6m x 5m with a sump and a smaller bund beneath the dosing valves, gives around 43m² of surface that must hold the full chemical if the tank ever leaks.
Sulphuric Acid Bund Lining – Bolton
THE PROBLEM
When we surveyed the bund, the existing lining had been badly degraded following a sulphuric acid leak. Large areas had blistered, flaked and broken down, and the acid had attacked the concrete beneath, eroding the sump and the joint between the walls and floor. We also found signs of poor application, with gravelling and blowholes in the concrete that had not been filled before the original coating was applied.
Our view was that the old lining had failed either because it was poorly applied or because it did not have enough chemical resistance for concentrated sulphuric acid. A bund in this condition can no longer be relied on to contain a spill, so it needed stripping back to sound concrete, repairing and relining with a system that would stand up to 96% acid.
THE SOLUTION
Removing the old lining
We removed the failed lining and the acid-damaged concrete using ultra high pressure water jetting. This takes off the old coating and weak, contaminated concrete without the dust of dry blasting, leaving a clean, sound surface. The jetting exposed a large amount of loose stone from the degraded surface, which we dug out and washed away between passes. With no drain available on site, the wash water was collected and taken away by tanker.
Fairing coat and coving
The walls were ground and vacuumed, and a cove was formed at every wall to floor joint so the lining runs round a smooth radius rather than a sharp corner, where coatings are most likely to crack. The whole bund, including the mini bund beneath the dosing valves, was then given a cementitious fairing coat of Sika TopSeal 586 to fill the blowholes and irregularities. Blowholes cannot be filled with coatings alone; left open they trap air that breaks through the wet coating and leaves pinholes.
Reinforced epoxy lining
When lining concrete a flexible system is usually preferred, but no flexible resin will withstand this level of chemical exposure, so the client chose our reinforced option. We primed the bund with Remmers Epoxy MT100, a damp tolerant epoxy primer, then applied a second coat of MT100 with chopped strand glass fibre mat laid into the wet resin. The glass fibre reinforcement gives the lining much better impact and crack resistance than a coating on its own. Once cured, the laminate was sanded to remove any raised fibres and defects.
Over the laminate we applied two coats of Resimac 511, an epoxy novolac lining that resists sulphuric acid up to 96%, to a nominal total of 1,000 microns. The first coat was applied in red and the second in grey, so the team could clearly see full coverage of each coat. Wet film thickness was checked as each coat was applied.
A dehumidifier was run in the bund during the coating work, and we tested and recorded the climatic conditions on each coating day with a PosiTector DPM. During coating the surface temperature stayed between 3.3°C and 10.3°C above the dew point, keeping it clear of the 3°C minimum needed to avoid condensation forming under the lining.
Testing and finishing
Once cured, the whole lining was spark tested with a holiday detector to find any pinholes or thin spots. A single pinhole is a point of failure in a chemical lining, so every holiday found was marked and touched in with the same material. Finally we sealed the joint between the tank base and the new lining with mastic.
THE RESULT
The bund now has a fully reinforced, chemically resistant lining that is fit to contain 96% sulphuric acid, with a rebuilt sump, coved joints and a continuous, spark tested finish.
We completed the works on site in two weeks, in line with the programme we quoted.
If you have a chemical bund or sump that needs repairing or relining, see our bund lining services.




























